11:18:40 AM NPT Arduino, Robotics & IoT tutorials for Nepal
Beginner

Soldering for Beginners: Tools, Safety and Your First Good Joint

Learn to solder for Arduino and robot projects: which iron and solder to use, safety rules, how to make a shiny joint, and how to fix cold joints and bridges.

On this page
Soldering for Beginners: Tools, Safety and Your First Good Joint

Breadboards are great for testing, but sooner or later a project has to be soldered. Motor wires on a robot, header pins on a sensor module, a circuit on perfboard for your exhibition. A bad joint causes the worst kind of fault: the project works on the table, then stops when you move it.

The good news is that soldering is a skill, not a talent. With the right tools and three simple rules, most people make good joints within an hour of practice. This guide covers the tools, the safety rules, the technique, and how to recognise and fix bad joints.

What you need

Scroll sideways to see all columns.

Item Notes
Soldering iron A temperature-controlled iron or station is easiest to learn on. A basic fixed-temperature iron also works for small jobs
Iron stand Never lay a hot iron on the table
Solder wire with rosin flux core Thin wire, around 0.6 mm to 0.8 mm, is easiest for electronics
Tip cleaner Brass wool cleaner, or a damp (not wet) sponge
Flux pen or paste (optional) Helps solder flow on old or dirty parts
Desoldering pump and/or desoldering wick For removing mistakes
Side cutters (flush cutters) To trim component legs
Helping hands or a small vice Holds the board still
Safety glasses Clipped leads and flux spatter can fly
Small fan To move fumes away from your face
Practice board Perfboard or a cheap practice kit, plus some resistors and header pins
Heat-shrink tubing For insulating wire joints

Leaded vs lead-free solder

Leaded solder (often marked 60/40 or 63/37 tin/lead) melts at a lower temperature and flows easily, which makes it forgiving for beginners. Lead-free solder needs a higher temperature and takes a little more practice, and is preferred where lead exposure is a concern. Whichever you use, wash your hands after soldering and keep food and drink away from your bench.

Safety rules first

Soldering is safe when you respect a few rules. The tip is hot enough to burn skin instantly and melt plastic, cables and clothes.

  • Always return the iron to its stand. Never leave it lying on the bench or on the cable.
  • Fumes: the smoke is mostly from the flux. Do not breathe it directly. Work in a ventilated room and use a small fan to pull fumes away from your face.
  • Eye protection: wear safety glasses, especially when cutting leads.
  • Wash your hands after soldering and before eating.
  • Unplug the iron when you finish or step away. Let it cool in the stand.
  • Never solder a powered circuit. Disconnect batteries and USB before you touch a joint.
  • Check the iron's cable and plug. If the mains cable is damaged, stop using it and get it replaced by a qualified electrician; do not tape it up and carry on.
  • Keep the cable clear of the hot tip and of your elbow so you cannot drag the iron off the bench.
  • Lithium cells: never solder directly to an 18650 or similar cell. Use a proper holder or a pre-made pack.

Prepare the iron

  1. Put the iron in its stand and switch it on. On a temperature-controlled iron, a setting in the low-to-mid 300s °C is a common starting point for leaded solder, and somewhat higher for lead-free. Check your solder's packaging for its recommended range.
  2. When hot, wipe the tip on the brass wool or damp sponge.
  3. Tin the tip: melt a little solder onto the tip so it is coated and shiny. A tinned tip transfers heat well; a dull, black tip does not.
  4. Re-tin the tip before you put the iron back in the stand, and wipe it between joints.

The three rules for a good joint

Rule 1: Heat the pad and the leg, not the solder

Touch the iron tip so it contacts both the copper pad and the component leg at the same time. Hold it there for about one to two seconds so both get hot.

Rule 2: Feed solder to the joint, not to the iron

Touch the solder wire to the joint on the side opposite the iron. The hot pad and leg melt the solder, and it flows around them. If you melt solder on the iron and drip it onto the joint, it sits on top as a ball and does not bond.

Rule 3: Remove the solder, then the iron, then do not move

Once enough solder has flowed to make a small cone, pull the solder wire away first, then the iron. Keep the parts still for a couple of seconds while the joint cools. Moving it while it solidifies makes a grainy, weak joint. The whole process usually takes only a few seconds.

What a good joint looks like

Scroll sideways to see all columns.

Joint Looks like Problem Fix
Good Smooth cone or "volcano", shiny (leaded) or slightly satin (lead-free), solder wets both pad and leg None Trim the leg
Cold joint Dull, grainy, lumpy, or a ball sitting on the pad Weak or intermittent contact Reheat with a little flux, add a touch of fresh solder
Too little solder Pad not fully covered, gap around the leg Weak joint Reheat and add solder
Too much solder Big blob hiding the pad May hide a cold joint or touch neighbours Remove extra with wick or pump
Bridge Solder joining two neighbouring pads Short circuit Drag the clean iron between pads, or use wick
Lifted pad Copper pad peeled from the board Overheated or forced Avoid long heating; repair with a wire link

Your first practice session

  1. Resistors on perfboard. Bend the legs, push them through, and solder ten joints in a row. Trim the legs with flush cutters after soldering.
  2. Header pins on a module. Many sensor modules in Nepal come with loose header pins. Push the pins into a breadboard to hold them straight, place the module on top, and solder one pin at each end first. Check alignment, then do the rest.
  3. Wire to wire. Strip a few millimetres from two wires, twist them together, solder, and slide heat-shrink over the joint before shrinking it. Always put the heat-shrink on the wire before you solder.
  4. Motor leads. For robot motors, tin the wire end first, then hold it on the motor tab and heat briefly. Do not overheat the tab, as the plastic behind it can melt.

Desoldering: fixing mistakes

  • Desoldering pump: cock the pump, heat the joint until the solder melts, place the nozzle on it and press the button to suck the solder away.
  • Wick (braid): place the braid on the joint, press the iron on top. The braid soaks up the molten solder. Cut off the used part.
  • Adding a little fresh solder to an old joint often makes it easier to remove.

Troubleshooting

Scroll sideways to see all columns.

Symptom Likely cause Fix
Solder will not melt or flow Tip dirty or not tinned; temperature too low Clean and tin the tip; raise temperature slightly
Solder balls up on the pad Pad not heated; dirty or oxidised pad Heat pad and leg together; use flux
Tip goes black quickly Left hot without solder on it Keep the tip tinned; lower temperature between joints
Project works only when pressed Cold joint or cracked joint Reflow every suspect joint
Board smells burnt, pad lifts Iron held too long or temperature too high Shorter contact time; let the board cool
Short circuit after soldering Solder bridge or leg touching Inspect under a light; remove bridges

After soldering, test continuity and shorts with a multimeter. Our multimeter testing guide shows how to use continuity mode.

FAQ

What wattage iron should I buy?

For small electronics, a temperature-controlled iron is more important than wattage. If buying a basic iron, choose one meant for electronics work, not a heavy iron for sheet metal.

Can I use any solder from the hardware shop?

Use solder wire with a rosin flux core meant for electronics. Avoid acid-core plumbing solder, which can corrode circuit boards.

Why do my joints look dull?

Lead-free solder naturally looks less shiny. With leaded solder, a dull grainy look usually means the joint moved while cooling or did not get hot enough.

Is soldering dangerous for students?

It is safe with basic precautions: a stand, ventilation, safety glasses, hand washing and never touching the tip. Younger students should solder with an adult or teacher present.

What should I solder first on a robot?

Motor wires. Loose motor wires are a very common reason robots "sometimes work". See the line follower robot build and the L298N motor driver guide for where those wires go.

Related tutorials

See all Electronics Basics →